King pin zerks
 

King pin zerks

Started by fe2_o3, August 23, 2011, 03:35:29 PM

Previous topic - Next topic

fe2_o3

    Lost the ability to get grease in to the king pins on both sides. I hope it's just a zerk issue, but to be sure we're going to stop at Kaisers in Eugene tomorrow. Any one have any experience with them? The appointment was made for us and we're thinking of running with it...Cable
Sofar Sogood
1953-4104
KB7LJR
Everett, WA.

Boomer

Kaiser is one of the most experienced and best shops in the country.  I HIGHLY recommend them.
'81 Eagle 15/45, NO MORE
'47 GM PD3751-438, NO MORE
'65 Crown Atomic, NO MORE
'48 Kenworth W-1 highway coach, NO MORE
'93 Vogue IV, NO MORE
1964 PD4106-2846
North Idaho USA

luvrbus

Amen to Dick Kaiser he's been a friend of mine for 20 years I drive a 1000 miles to get him to do my work tell him Clifford said hi and you can  pay double lol  

good luck
Life is short drink the good wine first

fe2_o3

Thank you Gentlemen... Your confidence in him allows us relax a little. We don't mind these little hiccups, as long as they are done right (and we can afford them)...Cable
Sofar Sogood
1953-4104
KB7LJR
Everett, WA.

Chopper Scott

Just don't forget to pay him double as Clifford stated. Sure don't want you to ruin it for everyone else! ;)
Seven Heaven.... I pray a lot every time I head down the road!!
Bad decisions make good stories.

fe2_o3

 I don't know about paying double...She who must be obeyed has a firm grasp on the finances, but I'll see what I can do! Maybe I'll tell them Clifford said I only had to pay half. We'll see what kind of trouble I can get into. After they're done...Cable
Sofar Sogood
1953-4104
KB7LJR
Everett, WA.

Kevinmc5

Seams like your in good hands. Only wish I could help you as you helped us. Good luck and  keep us posted
Kevin and Traci
1964 4106-2471 8v71 Boise ID Driving any place I can Fit

artvonne

  Maybe tell him Clifford said to tell ya he was picking up the tab. lol

luvrbus

No no put it on Marks (Boomer) account lol, Dick will put your bus on the front end pit and will tell you if you have problems if you do he won't waste your money trying to align it then you can repair it yourself and bring it back or he will do the work makes no difference to him he is not one to get PO if you want to do the work yourself a fine gentleman not like most shops.
I have a friend in Neb that drove his Prevost from Cambridge Neb to Eugene OR for Dick to do his work he is one happy camper now

good luck

PS he has 50 amp service for RV's and BBQ every Friday lol
Life is short drink the good wine first

AndyG

Sometimes there is a load on the pin which will prevent grease from entering.  Try turning the wheels left or right.  If turning the wheels does not work use a jack to remove most of the load from that wheel.  If it has been a long time since is was greased the old grease may be petrified and you cannot force new grease in.  Remove the zerk and scrape out the hardened grease with a wire or small screwdriver.  Put the zerk only into the grease gun and force fresh grease through it reinstall the zerk.  A bit of heat (or solvent if you are patient) will also soften hardened grease.  This should fix it if old grease is the problem.  These are a couple of the tricks that I use on my antique equipment that might work for you. 

Busted Knuckle

OH and just to take Andy's comment one step farther it used to be common practice and expected to jack up the front axle and take the weight off both sides when greasing the king pins! 
I haven't been in any shops where lubes are commonly done lately other than my own so I don't know if it's still common among the younger grease monkeys or not!
;D  BK  ;D
Busted Knuckle aka Bryce Gaston
KY Lakeside Travel's Busted Knuckle Garage
Huntingdon, TN 12 minutes N of I-40 @ exit 108
www.kylakesidetravel.net

;D Keep SMILING it makes people wonder what yer up to! ;D (at least thats what momma always told me! ;D)

artvonne

  There is a tool you can buy, I think Napa can order one. Its a grease gun you hit with a hammer. Ive never used one, but supposedly it was made for situations like this, the tool generates pressures much higher than normal grease gun to force grease past the blockage and blow new grease through. Might well be worth the price.

bevans6

I just (well, a year ago) went through this.  In my case my kingpins are very new and were installed tight.  I had my success with  taking the zerk out, installing a fitting and direct-connecting a brand new high pressure pump gun, and pumping Marvel Mystery Oil (any solvent type fluid would have done) in over a period of days, coupled with heat, jacking up, jacking down, swivelling the hub, cursing, etc.  Eventually I got movement.  It took a long time.

Brian
1980 MCI MC-5C, 8V-71T from a M-110 self propelled howitzer
Allison MT-647
Tatamagouche, Nova Scotia

fe2_o3

   Kevin, Thanks, It's always nice to have someone on the other end of this thing. It can get lonely when things go bad on the road.
   Clifford, Dick wasn't there. His son said he got a new Camaro and was trying it out, so he's on his way to Montana.
   They did just like Clifford said. They put her on the rack and started checking her out. They were able to get grease into the proper areas and forced the old grease out. The check up went well. No major problems and we were sent packing for a reasonable cost. I wouldn't hesitate to recommend or return. Great people to do business with. Thanks to all of you for your support...Cable
Sofar Sogood
1953-4104
KB7LJR
Everett, WA.