Where do you get the Aluminum Molding for covering the seams?

[Dreamscape]

I have googled, MAK search and Help. Could not find what I am looking for in aluminum trim moulding. I want to replace the trim that goes between the side panels on upper and lower. I would rather not have a plastic insert. Would like to find one that is similar to a half round with ridges on under side to go over rivets. Any suggestions on what is best?

Thanks in advance.

Paul

[DavidInWilmNC]

Paul,

Maybe something like what MCI used on the -8's and -9's right under the windows would work.  It's a long section of molding that's maybe 1-3/4" wide and maybe 1/4-3/8" or so tall (this is from memory so the dimensions may be off).  Perhaps somebody who removed it from their MCI would have it, or most parts buses would, too, I'm sure.  This is definitely not half round, but might still work for you.

David

[pete81eaglefanasty]

 Hi Paul
I believe what you are looking for, you can get from I B P They come in 20 foot length. I got a few from them.

            Pete & Jean
              FANTASY

  #1-800-468-5287

[Dreamscape]

David,

Thanks for the information. The width is about what I need, no less than 1 1/12".

Pete,

I checked their web site, didn't find what I need. I'll have to give them a call. The 20' length is perfect, as that is what the old stuff was.

Thanks for the help,

Paul

[Nick Badame Refrig/ACC]

Hi Paul,

I have IBP's PDF catalog on my computor and I can't figure out how to post it yet...

I also purchaced Eagle moldings from them and now that I'm thinking about it I think I have 2- 20' ers left...

Nick-

[pete81eaglefanasty]

 Paul
I just look at their book it is called cover molding # BS 2272-141
them you will want to get  the Molding seal that goes under the aluminum strip it makes the strip fit and looks better. #BS 2672-318D


              Pete & Jean
                FANTASY

[Nick Badame Refrig/ACC]

Hi Paul,

This is the Eagle moldings that I installed on my bus.

Nick-

[FloridaCliff]

Nick,

Send me the pdf as an attachment to my email, when you have a chance.

I have an interest in some mouldings also.

I couldn't find it online!

Thanks

Cliff

[muddog16]

I bought all of my trim from Austin Hardware they have a great catalogue  here is there website link:   http://www.austinhardware.com/

[Dreamscape]

Hi Nick,

What was the part number of the one you used?

Thanks for the help guys.

Paul

[FloridaCliff]

Pat,

Thanks for the link.

Looks like they have what I need.

Cliff

[Nick Badame Refrig/ACC]

Hi Cliff,

I was not able to e-mail it either???.  I have it on disc too..

Hope you have it now.

Nick-

[mikeH8H-649]

Cliff,I have a copy of IBP's pdf if you would like it,GM's are all most obsolete on it allthough they still make the panels for them they are pretty much a special order thing,Kathy and I were there a few weeks ago and Steve says there is just not much call for gm's anymore which makes sense,let me know if you want it and I will get it to you     Mike                                                                                               

[Sojourner]

http://www.extrude-a-trim.com/pdfs/Boat_and_RV.pdf
They have aluminum rub rail with 1/8" lip (over rivet) to screw on and snap vinyl trim to cover...made for RV.

It good idea to leave some gap on bottom of rub rail for moisture relief.

FWIW

Sojourn for Christ, Jerry

[boogiethecat]

McMaster has some really  nice stuff:

go to http://www.mcmaster.com/ and type "aluminum moulding" into their search engine, or go to page 3659 in their online catalog

I just glue it on with Sikaflex.... works great!

Cheers
Boogie