I greased the bearings on the radiator drive @$#'y (pillow blocks?) before I left on the trip home w/ my new bus. At that time, they looked as though they had not been greased for a long time. :-\
As you can see in the pictures, the bearing seal (?) seems to have gone away. :o
What is the best way to get at these? Which bolts need to come off to get the bearings replaced? ???
It looks as though the shaft comes apart where there seems to be a rubber bushing (?) as seen in second photo.
I don't exactly know what I am doing, but I know the bearings need replaced. :'(
Any tips, advise, opinions, complaints, help, or comments would be very much appreciated! :)
HELP!
thanks
Mark
(https://busconversionmagazine.com/forum/proxy.php?request=http%3A%2F%2Fxs216.xs.to%2Fxs216%2F07262%2FIMGP2359.JPG.xs.jpg&hash=cc91fbd46721ab84514f655045e282d4ad698680) (http://xs.to/xs.php?h=xs216&d=07262&f=IMGP2359.JPG)
(https://busconversionmagazine.com/forum/proxy.php?request=http%3A%2F%2Fxs216.xs.to%2Fxs216%2F07262%2FIMGP2360.JPG.xs.jpg&hash=9235bf6b7ec6356f9738d5229f7b51a54e3ca78f) (http://xs.to/xs.php?h=xs216&d=07262&f=IMGP2360.JPG)
Mark that one looks easy just take the 4 bolt out of the 2 bearing and your belts should be loose and pull it out of the coupling and remove it out of the bus where you can see how the pulley comes off good luck
Mark
Looks like the bearings. are shot! The replacement should not be to bad if they have not slipped on the shaft. Use plenty of rust buster or equivalent spray all bolts,set screws etc. next remove the belt,mark the flex connector(may not be necessary but get everything back in the same location ) unbolt the four bolts holding the pillow block bearings in place,remove the shaft assembly and clean it off(you may need to lightly sand the rust from the shaft),next check the bearing to shaft retainer (it should be held in place with ether set screws only or set screw holding an eccentric locking Collier ----look closely at the locking device the eccentric will have an untapped hole around the shaft from the set screw if it does remove the set screw use a chisel an hammer firmly tap the locking Collier in the opposite direction of normal shaft rotation to loosen Collier an slide away from bearing,next mark the shaft using a hack saw or scratch awl ,remove the sheave by removing the two or three bolts holding sheave to the inner hub an thread these into the holes next to where you removed the first bolts tighten the bolts evenly an press the sheave apart . remove the hub,bearings, etc. install new bearings( make sure you set the locking colliers toward the direction the shaft normally rotates.
Hope this helps :)
Dwayne
They look like standard 2 bolt pillow block bearings to me. Get the numbers off the casing and race, should be able to find those pretty easy. Truck parts place, Kaman bearing are just to name a few.
Happy Trails,
Paul
Dreamscape
Take off the assy by removing the 4 bolts holding the bearings on. The coupling has a rubber spider that will slip apart by simply pulling apart. Clean the assy well & take it to a local bearing distributor. He can identify the bearings & get you the best price (usually). Show him the spider & get a new one (required if there is any play in the connection).
Have fun! The education has already started ;D
Thanks guys
It only seems like a dreaded repair to me because of the location of the bearings. Not sure how I will get myself back into that area - tight squeeze! I can only contort myself so as to get one arm at a time on the bolts. Will need to figure a way to back up the nuts somehow(?)
thanks again!
Mark
Luvrbus is right, remove the bolts that hold the pillow block bearings on and remove the whole shaft/pulley assembly. It will be much easier to work on if you can do that. Pillow block bearings are not all that expensive and you have several different types of locking mechanisms to choose from, like set screw, taper lock, cam-lock etc. If they are really rusted on, take a hammer and bust the cast iron block off, and then torch the center race off. Use emery cloth to clean up the shaft If the new bearings are still hard to get on, use the old center race and a hammer to aid in installation.
I agree, that bearing looks to be missing some Testicles..
replace them for sure.. ;D
Paul...
Can't really tell from the pix, but If you can get under it safely, put a box end wrench on the bolt head and go after the nuts from the bottom with a socket and extension. With luck the wrench will stay on and wedge against something. Just make sure it is not the radiator core. The box end wrench will bounce off your forehead for sure (you are of course wearing your safety glasses) but if you keep after it you will get there.
Sometimes an impact gun will spin a nut off a loose bolt without holding the bolt at all. Hint, leave the belts on to put some sideways pressure on the bolts until you get the nuts off. If all else fails after you break them loose, put a pair of vise-grips on the bolt head to hold it while you remove the nuts.
This from someone who works by himself a bunch.
Don, get a bigger hammer, 4107
Any chance someone here might have the part numbers for the bearings?
I haven't had time to get at these bearings yet, & I would like to have the replacements here when possible so I can make it to Busin USA in two weeks!
I will need to replace the two fan belts at the same time. Part number for them too?
The bus is a 1967 Prevost Champion w/ 8V-71, Allison auto.
The only manuals I have are for a H3 (?) came w/ my bus
thanks!
Mark
not too many early Champions running around. Don't know of another one on this board that is active anyway.
If you want them on hand for the job I would call Prevost Parts and ask them.
Otherwise, pull them and get the numbers off them or take them to a bearing house and have them measured
Yes, I noticed the lack of Prevost Champion owners... :-\
Hope thats not for some reason... :-[
Lots of early GM's, Eagles, MCI's. What happened to the early Prevosts? ???
Mark
low production numbers...with most living in Canada and succumbing to old age/elements and the like.
Don't know of any bad traits
YIKE...YIKE....it look like it hasn't been grease along time...fitting is dirty coated plus very dry looking around bearing pillow block casting. Usually it is greasy for normal. Good thing you are not break down else where.
Parts you need are industrial & machinery type. Prevost get them for a bearing supplier...not a special made part.
Look up for Grainger 1-888-361-8649 Monday-Friday, 24 hours a day, 7 days a week or any industrials supplier near by. Ask any manufacture near by to locate their industrial supplier with phone number. Unless you have a large phone book...look in industrial section.
Take the parts...shaft & what left of pillow bearing to get matching size. While this far into...get 2 sets. I am sure by now the other is get ready to blow.
This time be sure to get the correct manual so you can locate all your lube points & grease as manual requested. Then you can go with one less reason to break down.
Wish you well getting it done soon & be careful to limited your cuts & bruise. Hope none.
FWIW
Sojourn for Christ, Jerry
Take everything off, go to a bearing dist. They should be able to match everything. That way you can match it all, and buy the correct spares for the next time. If you grease it properly it should last many years, using the proper grease and the proper amount, you may never need to use the spares.
Happy Trails,
Paul
Dreamscape
Quote from: Dreamscape on June 27, 2007, 08:49:05 PM
Take everything off, go to a bearing dist. They should be able to match everything. That way you can match it all, and buy the correct spares for the next time. If you grease it properly it should last many years, using the proper grease and the proper amount, you may never need to use the spares.
Happy Trails,
Paul
Dreamscape
The bearing distributors I used to deal with
did not recommend we provide spares with the machinery we built. Their explaination was that the bearings would probably sit for many years before needed, and that the grease would seperate during that time.
Regarding spell check, it found two words incorrect in this message as I typed it which I have not corrected.They are explaination and seperate. Correct spelling is explanation and separate.Richard
Quote from: DrivingMissLazy on June 28, 2007, 07:58:45 AM
Quote from: Dreamscape on June 27, 2007, 08:49:05 PM
Take everything off, go to a bearing dist. They should be able to match everything. That way you can match it all, and buy the correct spares for the next time. If you grease it properly it should last many years, using the proper grease and the proper amount, you may never need to use the spares.
Happy Trails,
Paul
Dreamscape
The bearing distributors I used to deal with did not recommend we provide spares with the machinery we built. Their explaination was that the bearings would probably sit for many years before needed, and that the grease would seperate during that time.
Regarding spell check, it found two words incorrect in this message as I typed it which I have not corrected.They are explaination and seperate. Correct spelling is explanation and separate.
Richard
SMARTY PANTS, SHOWOFF ;D ;D ;D
Seriously I think that is great, hope others will consider Firefox.
Paul
Last summer I had a bearing fail on an air-conditioner fan motor. I was in northern Montana at the time, a long way away from any Prevost dealer. I called the Prevost parts dept and they gave me equivalent bearing numbers for a major bearing mfg, and the local shop (in a town of about 25,000) had the correct bearing in stock. way cool.
You might try them too.
AS always buy new extra bearings, this will guarantee you will never have any more problems with them again ;D just never leave them at home with out them or they will always fail :o
Dwayne
funny about not leaving home without the spares. We collected a huge inventory of new parts for my 04 during the 30 years we owned it.......if I carried all the spares I thought I may need I would not have any room for anything else.
Spares I carry: Headlights, marker light bulbs, Oil Filter, Fuel Filters, blower shaft
of course you full timers or snowbird types might carry a bit more.
but I have not really had any issues with finding things on the road. Worst case they are an overnight shipment away
Be bold
Carry no spare parts.
Better inspiration to keep up with the preventive maintenance?
happy coaching!
buswarrior
I would not carry those bearings as a spare as they are not an item that has a very high failure rate, especially if you do your preventive maintenance. Also, pillow block bearings are very common, and unless they are some sort of proprietary size that was made for that application, there should be no problem finding them.